How to Install and Configure Raid Drives (Raid 0 and 1) on Your PC

A geeky trick that will speed up your read/write

When my father told me that he was running his computer in Raid 0, I was confused as to why he would want such a configuration. To my knowledge, running a Raid configuration was outdated and complicated to set up. Then I did my research.

There are significant advantages to running your computer in a raid configuration. The most common raid configurations for home use are Raid 0 and Raid 1.

Raid 0 gives you better performance, as it focuses on distributing data evenly on multiple drives (instead of using one drive as a backup), significantly increasing read/write speeds of your machine.

Raid 1 gives you better data insurance, as it creates an exact copy of data from one hard drive to another, constructing full redundancy through backups. Setting up your hard drives to run in a Raid configuration is a personal decision based on your setup and you should decide which iteration is best for you. I personally prefer Raid 0, because I prioritize computer speed and performance over data security and redundancy.

Before starting

If you’re planning on implementing a raid setup on your current machine, make sure you create abackupof all of your data, as it will beerasedin the process. You will also need Two separate flash drives with enough space for their respective files.

On the first flash drive you will need to download the Raid drivers. You can find thosehereafter you select your machine and model. On the second flash drive you will need to download the windows ISO. You can find that download linkhere.

It’s possible to install both files to a single flash drive but there have been reports of system instability during startup, so I wouldn’t risk it. Let’s begin.

Setting up Raid 0 or Raid

1

I briefly mentioned the benefits of each iteration of Raid, but with all advantages in life, come their respective disadvantages. Since Raid 0 distributes your data to multiple drives, if a single drive fails, all of the data on the other drives will be gone as well. The disadvantage of Raid 1 is that it’s significantly slower than Raid 0.

That being said, Raid 0 and Raid 1 are both super easy to set up and require basically the exact same setup process. The first thing you’re going to want to do is figure out if your motherboard has a built in Raid controller (most modern motherboards do).

From here you should:

Once you’re there your screen will look like the one in the picture below. From here you should navigate to your BIOS equivalent of thechipset. This screen will look something like this:

After navigating to yourchipsetyour screen will look like this:

From the chipset screen, you should navigate toSATA Modeand selectRAIDinstead ofAHCI.

You have now successfully initialized Raid on your motherboard; simply hitSave & Exit. The computer will restart at this point and will attempt to launch a copy of windows that isn’t there anymore.

Simply press and holdCtrl + Rto launch the Raid controller user interface (Ctrl +R for AMD, this combo may vary for your setup). At this point your screen should look something like this:

After reaching this point you should selectCreate Arraythen select the drives you want to use for the raid configuration. The drives available will be listed on the right-hand side underDisks. Use theAorInskey to select the drives and hitenterwhen you’re finished configuring the disks.

After you’ve done this your screen will look like this:

From here you can decide which configuration you want to select. I personally selected Raid 0 but the choice is yours. After this you will choose the size of the array you want to build.

I just kept the default setting of usingAll Available Spacefor my raid drives. After this you will select the caching mode, I have kept the default caching systemRead/Write. This will look something like this:

After configuring it to your liking simply pressCto create your array. PressEscandYto restart your system with your new Raid configuration.

After rebooting, navigate back to your BIOS and select your new raid configuration for the boot disk. Before hittingSave & ExitYour screen should look something like this:

After doing this your machine will restart again. Allow it to go through the normal startup process. It will prompt you of a driver error at which point your screen should look like this:

If you haven’t done so already, plug in the flash drive that contains yourRaid Driversand the flash drive that contains yourWindows ISO, navigate to the drive and folder where the driver is stored and hitOK. Your screen should look like this:

Select the drivers you need for the installation then click onNext. After doing this your screen will prompt you to select the drive you want to install your new Windows 10 Operating system on then click onNextagain. Your screen will look like this:

Your operating system will now begin installing. From here, you should be completely set up in whichever raid configuration (0 or 1) you chose. If you have any questions or if you need further elaboration on a specific part of the process let me know and I will get back to you immediately!

Enjoy the world of redundant arrays of independent disks (RAID).

Writer for Switching to Mac, Online Tech Tips, and Help Desk Geek blogs. With a background in IT and Physics, Christian has experience with computers, music, photography, and augmented reality technologies.Read Christian’s Full Bio

Welcome to Help Desk Geek- a blog full of tech tips from trusted tech experts. We have thousands of articles and guides to help you troubleshoot any issue. Our articles have been read over 150 million times since we launched in 2008.

HomeAbout UsEditorial StandardsContact UsTerms of Use

Copyright © 2008-2024 Help Desk Geek.com, LLC All Rights Reserved